Mitsubishi Electronics P91DW User Manual

This digital monochrome printer complies with the requirements of the EC Directive89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC.The electro-magnetic

7Rear PanelSelect special functions.Mode switchesPARALLEL data terminalFunctionNameReferencepage1010Connects to the device equipped withparallel data

8 Close the door. INSTALLATION OF PAPER5Moisture, fingerprints or dust on thepaper surface may cause a noise atprinting or deterioration in printquali

9When setting the paper, observe the followingprecautions to prevent paper jam.Do not use the bent or wrinkledpaper.Do not use defective paper.Do not

10 EXAMPLE OF CONNECTION6Connecting to various equipment with parallel data interfacesuch as medical equipment and personal computer.ConnectionTurn of

11 PRINTING7Printing procedureYou can set the number of copies bypressing the COPY button on the frontpanel. You can copy the same picture asmany tim

12By pressing the "FEED" button on thefront panel, you can feed the paper.Paper feedingIf printing is continued with a very black picture, t

138 ADJUSTMENT OF PRINT PICTURESelection of Gamma (γ) Curveγ−curve setmodeYou can select γ-curve by pressing the gamma button " ".Each time

149SETTING OF FUNCTION MODESelect a function mode by pressing the FUNC button.Paper type selection modePaper saving modeSet condition printing mode Bu

15Adjustment contentsIndicator/AdjustableitemPrinter condi-tion printingmodePaper savingmodePaper typeselectionmodeMode to select paper type. : Standa

1610When an error in operation occurs, an audible alarm and avisible error is displayed in the LED indicator.Cause/Error displayCause/Error displayCau

WARNING:Use the AC power cord recommended as below and a parallel cable (Hewlett PackardC2951A, etc.) so as not to interfere with radio and television

17Cause/Error displayCause/Error display[Symptom]• When the door opens, an alarm tone is given.Symptom/RemedySymptom/Remedy[Remedy]Close the door.[Sym

1811Set state/ModeLED displayLeftPoint andrightContents of rightside LED displayPower offStand-byPrint statePaper type setting modeγ-curve set mode (γ

1912When the thermal head is dirty with dust and perspiration, etc., white spots or stripes mayappear on the print. In this case, clean the thermal h

2013• Connector JD36SL or equivalent (36 pin)• Input level TTL• Parallel input connector port Signal allocation (Signal : Compatible) PARALLEL DATA

21Pin No.Return pin No.SignalFrom/ToFunction119HostClkPC/DPHighUnknownSends data in “Low” when HostBusy is “Low”. After HostBusy turns “High”, this s

22Pin No.Return pin No.SignalFrom/ToFunction119HostClkPC/DPForward data transfer : Becomes “Low” when PeriphAck is “Low” and there is data to be read.

2314 MAINTENANCETurn off the power for maintenance.Maintenance of Main UnitWipe off stains of the front panel with a soft cloth.When the panel is heav

2415 SPECIFICATIONSType: Digital Monochrome PrinterModel: P91DWPower supply andpower consumption: 120V AC, 50/60Hz, 1.4A220-240V AC, 50/60Hz, 0.8AConn

MITSUBISHI ELECTRONICS AMERICA, INC.5665 PLAZA DRIVE P.O. BOX 6007CYPRESS, CA 90630-0007, USATEL (714)220-2500 FAX (714)236-6339Made from recycled

The lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of uninsulated "dangerous

1CONTENTS... 1PRECAUTIONS ... 2 - 4UNP

2In the interest of safety, please observe the following pre-cautions:POWER REQUIREMENTThis Digital monochrome printer is designed for opera-tion on 1

3FOR LONG OPERATING LIFEUNSUITABLE MATERIALS FOR THE UNITMany plastic components are used in the backside. Coatflaking and deformation are likely to o

4SAFETY TECHNICAL CHECKSPeriods: According to the recommendations of the manufacturer of medical device.Scope: a) Visual checkHousing, cables, operato

5 UNPACKING3Open the top of the box. Remove the cushion above the unit.• Make sure tokeep the unithorizontal.Take the unit out of the box carefully.Ta

6 FEATURES AND FUNCTIONS4Front PanelTurns on/off the power.Power switchFunction mode changes whenever FUNCis pressed.FUNC buttonPress to change the va